Tattoo foot switches fall into two groups. By connection, they are wired (a pedal with a cord that plugs into the power supply, usually through an RCA or a 1/4-inch phone connector) or wireless (a pedal that talks to a receiver or a compatible power supply). By switching action, they are momentary (the machine runs only while you press) or latching (one press turns it on, the next turns it off). The right choice is the one your power supply officially supports, and at BVShop (Beauty Visit Shop) we sort foot pedals and power supplies together so you can check that match in one catalog.
This guide explains each type in plain terms, how a pedal actually works in the circuit, where wired and wireless setups differ in a working studio, and how to verify compatibility before you order.
Key Takeaways
- Connection type decides what fits: wired pedals use a cord and a specific plug style, while wireless systems depend on the brand and protocol of the power supply.
- Wireless is not universal. The Critical CXP19 wireless pedal is supported on XRR and Atom X-R power supplies, and the Critical Connect foot switch needs compatible Critical Connect hardware.
- Most tattooing relies on a momentary action, because the machine stops the moment you lift your foot.
- A wireless pedal is not a wired pedal without the cord. It is a separate system with its own pairing and receiver requirements.
- Before buying, confirm connector, wiring and manufacturer-listed compatibility on the product page or in the manufacturer’s documentation.
Table of Contents
- What a Tattoo Foot Switch Actually Does
- The Main Tattoo Foot Switch Types
- Wired Foot Switches
- Wireless Foot Switches
- Wired vs. Wireless: A Studio Comparison
- Momentary vs. Latching Foot Switches
- How to Check Compatibility Before You Buy
- Matching the Pedal to the Power Supply
- Choosing for Your Kind of Work
- Build Details That Matter Over Time
- Shopping at BVShop
- FAQ
- Sources
What a Tattoo Foot Switch Actually Does
A foot switch is a control, not a power source. The power supply sends low-voltage DC current toward the machine, and the pedal closes or opens that path. Press the pedal and the circuit closes, so the machine runs. Release it and the circuit opens, so the machine stops. Voltage is still set on the power supply itself, which is why the pedal never replaces a good power unit. If you are still matching voltage to the job, our tattoo machine voltage guide covers lining, shading and color.
This circuit view is useful for troubleshooting too. If a machine does not respond, the fault may sit anywhere in the chain: the pedal, the cable, the connector, the clip cord, or the port you plugged into. A pedal in the wrong jack, or a plug that is not fully seated, can look exactly like a dead machine. Before you suspect the machine, swap one part of the chain at a time.

The Main Tattoo Foot Switch Types
It helps to classify pedals on three separate axes. A single pedal sits somewhere on each one.
| Axis | Options | What it decides |
|---|---|---|
| Connection | Wired (RCA, 1/4-inch phone plug, banana-plug style clip cord setups) or wireless | Which power supplies it can plug into or pair with |
| Switching action | Momentary or latching | Whether the machine runs only while pressed |
| Build | Pedal shape, base, housing, cable length | Comfort, stability and how well it handles a working station |
Most buying mistakes happen on the first axis, so start there.
Wired Foot Switches
A wired pedal is the traditional setup. A cable runs from the pedal to a jack on the power supply, and the circuit is completed through that cable. There is no pairing, no battery in the pedal and no radio link to configure. The cord is the part you manage.
RCA connector pedals
RCA is a round plug with a center pin and an outer sleeve, the same family of connector used on audio equipment. Many current power supplies take an RCA pedal, and the plug is simple and holds firmly when seated. If your power supply has an RCA foot switch port, an RCA pedal is the straightforward match.
1/4-inch phone-jack pedals
The 1/4-inch phone plug is the larger, cylindrical jack. It appears on older coil setups and some entry-level power supplies, and many power supplies carry phone jacks for both the clip cord and the pedal. These two ports can look identical, so label them or check the markings before plugging in.
Pedals paired with clip cords
Some setups ship a pedal and a clip cord as a pair, with banana plugs on the clip cord end. In this case the pedal and the cord are separate parts, and each needs to match its own port. Treat them as two compatibility checks, not one.
Where wired pedals work best
- Stations where you want no batteries, no pairing and no interference to think about.
- Studios with fixed layouts where a cable run is predictable and out of the walkway.
- Artists who value a pedal that behaves the same way every session.
The practical limits are physical: a cable can snag on a chair base, get stepped on, or pull a pedal out of position if you shift during a long session. Cable length matters, so measure the distance from the pedal’s position to the power supply before you order, and leave slack so the cord is never under tension.
BVShop lists the Critical Tattoo CXP wired foot pedal among its foot switch options. Check the product page for its connector and listed compatibility against your power supply before you order.
Wireless Foot Switches
A wireless system replaces the cable between pedal and power supply with a radio link. In practice that usually means a pedal that transmits and either a receiver unit or a power supply with a built-in receiver. Because the link is a protocol and not a standard plug, compatibility depends on the brand and the specific model. A wireless pedal from one maker does not automatically work with another maker’s power supply.
That is the point owners most often get wrong, so state it plainly:
- A wireless tattoo machine is not a foot switch. A cordless machine runs on its own battery and has nothing to do with the pedal question. Do not confuse the two when you compare options.
- Wireless pedal compatibility is manufacturer-specific. Read the product page for the supported power supplies.
- There is no universal wireless standard across brands that a buyer can rely on.
CXP19 wireless: XRR and Atom X-R
The Critical Tattoo CXP19 wireless foot pedal is supported on XRR and Atom X-R power supplies. In the BVShop catalog these are the Critical Tattoo Power Supply XRR and the Atom X-R units, such as the Atom X-R Rosegold/Black and the Atom X-R Rosegold/White. Do not assume CXP19 support extends to other power supplies in the same family. The Atom X models without the R, for example, are separate listings, and you should check each product page before pairing.
Critical Connect: needs Critical Connect hardware
The Critical Connect foot switch belongs to the Critical Connect system and requires compatible Critical Connect hardware. It is not a drop-in pedal for any power supply. If your current power supply does not carry Critical Connect support, this pedal is not the match, and a wired pedal that fits your existing ports is the simpler path.
Where wireless works best
- Stations where a cable across the floor is a trip risk or gets in the way of a chair.
- Studios that rearrange stations between clients and want the pedal to move freely.
- Artists who already run a power supply designed for a specific wireless pedal.
A wireless setup adds things to manage: pairing, any battery or charging requirement the manufacturer lists, and the receiver’s position. Read the manufacturer’s instructions for those, because they differ by system.
Wired vs. Wireless: A Studio Comparison
| Consideration | Wired | Wireless |
|---|---|---|
| Compatibility | Determined by the plug and port (RCA, 1/4-inch) | Determined by brand, model and protocol |
| Setup | Plug in and check the connection | Pair or link to a supported unit, per the manufacturer |
| Floor layout | Cable must be routed and kept slack | No cable between pedal and power supply |
| Power needs | None at the pedal | Check the manufacturer for battery or charging requirements |
| Swapping between power supplies | Easy if ports match | Only within the supported system |
| What to verify | Connector, wiring, cable length | Listed supported power supplies and hardware |
Neither is the better setup in the abstract. The wired pedal is the lowest-friction option if your power supply has the port. The wireless pedal is the cleaner option if you run a power supply that the manufacturer lists as supported. Because many studios run more than one power supply, a useful approach is to standardize on one system per station so each pedal has exactly one job.
Momentary vs. Latching Foot Switches
This is the second axis, and it describes behavior, not connection.
- Momentary: the circuit is closed only while the pedal is pressed. Release it and the machine stops.
- Latching: one press closes the circuit and it stays closed until you press again. Switch makers describe the idea as a footswitch that stays on after a single press, as Herga explains in its technical note on latching footswitches, where tattooing is even named as a use for the latching style.
For the majority of tattoo work, the momentary action is the working norm. The machine runs when you press and stops when you lift, which gives direct control during lining, stops while you wipe, and an immediate cut-off if the client moves. A latching action can leave the machine running while your attention is elsewhere, so if you consider one, think about how you will handle the moment between presses. Whichever action you choose, confirm the manufacturer’s listing, because the action is part of the product’s design and not something you set.
How to Check Compatibility Before You Buy
Compatibility is a short checklist. Run it for every pedal and power supply pair, in this order.
- Identify the port on your power supply. Look at the back or side panel. Is the foot switch port RCA or a 1/4-inch phone jack? Note whether the unit instead lists a wireless receiver or a specific wireless system.
- Separate the clip cord port from the pedal port. On units with two similar jacks, a pedal in the clip cord jack will not behave correctly. Check the markings and the manual.
- Match the plug style. A wired pedal’s plug has to match the port. Do not rely on adapters unless the manufacturer lists them as supported.
- Read the listed compatibility. For wireless pedals, the product page or manufacturer documentation names the power supplies or hardware it supports. If your model is not named, treat it as unsupported.
- Check wiring requirements. If a pedal is sold with a clip cord or specific wiring, confirm what each part connects to.
- Measure the cable length. For wired pedals, measure from the pedal’s resting spot to the power supply and add slack.
- Test the full chain on arrival. Plug everything in, set a low voltage, and confirm the machine starts on press and stops on release before a client is in the chair.
Avoid unsupported cross-brand claims. A forum post saying two brands work together is not a substitute for the manufacturer’s own compatibility statement, and wireless links in particular are brand-specific.
Common failure points
- A plug that is not fully seated, which opens the circuit and looks like a dead machine.
- The pedal in the clip cord jack, or the clip cord in the pedal jack.
- A damaged or pinched cable, usually near the plug or under the pedal.
- Pairing a wireless pedal with a power supply that is not on its supported list.
- Choosing a pedal for its look when the port is the wrong type for your power supply.
When the machine will not start, walk back through the chain one component at a time rather than replacing everything at once.
Matching the Pedal to the Power Supply
The pedal choice and the power supply choice are one decision. If you are buying both, start with the power supply and its available ports, then pick the pedal. Our tattoo power supply guide covers choosing, setup and care, including what the panel connections mean.
In the Critical range, a practical path looks like this:
- You want a wireless pedal: look at the XRR or Atom X-R units for the CXP19, and at Critical Connect hardware for the Critical Connect foot switch.
- You want a wired pedal: choose a power supply with the matching foot switch port and a wired pedal that fits it, such as the CXP wired pedal.
- You run an existing power supply: keep your current port in mind first and shop for a pedal that fits it, not the other way around.
The Critical Tattoo Power Supply CX1-G2 and the Atom X Black are also in the catalog. Read each product page for its listed ports and supported accessories before you decide which pedal pairs with it, and do not infer wireless support from the family name.
Choosing for Your Kind of Work
Tattoo artists in a fixed station. A wired pedal that fits your power supply’s port is the lowest-maintenance route. Route the cable along the base of the chair and keep it clear of your seat’s wheels.
Artists who move stations or guest spot. A wireless pedal can reduce the amount of cable you set up and tear down, provided your power supply is on the supported list. Pack the receiver or any required hardware with the pedal.
Studio owners equipping several stations. Standardize. Using the same pedal and power supply pairing across stations makes spares interchangeable and cuts down on wrong-port mistakes. Keep a spare pedal of the type each station uses.
Students and academies. A simple wired pedal that matches the power supply is a clear starting point, with fewer settings to learn. The pedal is a safety control as much as a convenience: students learn to stop the machine by lifting the foot.
PMU and microblading specialists using machines with power supplies. The same rules apply. Confirm the port and listed compatibility for the specific power supply you use. Hygiene on the pedal is also worth planning for, since it sits on the floor and is touched by a shoe, then a hand when you adjust it. Studios commonly keep pedals covered or positioned so the pedal itself is not a point of contact with clean surfaces.
Build Details That Matter Over Time
Once connection and action are settled, the build decides how the pedal lives in a studio.
- Base grip. A pedal that slides is a pedal you look down at. Look for a base designed to stay put on your flooring.
- Housing and weight. A sturdier housing resists being stepped on awkwardly or kicked.
- Cable strain relief. On wired pedals, the point where the cable meets the pedal is the usual failure point. Check how it is protected.
- Cleanability. A smooth housing is easier to wipe down between clients than one with many crevices.
- Plug quality. A snug fit matters more than appearance.
Product pages list materials and design details for each item, and manufacturer documentation is the best source for specifics. If a detail is not stated, do not assume it.
Shopping at BVShop
BVShop (Beauty Visit Shop) is an online supplier of professional tattoo, PMU, microblading, piercing and beauty supplies, including power supplies and accessories, so foot switches and the power units they connect to are in the same catalog. That makes the compatibility check practical: you can open a power supply page, read its ports and supported accessories, then open the pedal page and compare. Browse the full range from BVShop, or go straight to the Critical CXP19 wireless foot pedal, the CXP wired foot pedal or the Critical Connect foot switch.
Shipping terms, availability and prices depend on your destination and are shown on the product pages and at checkout, so check them for your country before you order.
FAQ
What are the different types of tattoo foot switches?
By connection, there are wired pedals (RCA or 1/4-inch phone plug) and wireless systems that link to a receiver or compatible power supply. By action, there are momentary pedals, which run the machine only while pressed, and latching pedals, which stay on until pressed again. Build and cable length vary by model.
Does a wireless tattoo foot pedal work with any power supply?
No. Wireless compatibility depends on the manufacturer and the specific system. The Critical CXP19 wireless pedal is supported on XRR and Atom X-R power supplies, and the Critical Connect foot switch requires compatible Critical Connect hardware. Always read the product page for the supported units.
Is a wireless tattoo machine the same as a wireless foot switch?
No. A wireless machine is a cordless machine with its own battery and control. A wireless foot switch is a separate pedal that sends a signal to a compatible receiver or power supply. Buying one does not give you the other.
Should a tattoo foot switch be momentary or latching?
Most tattoo work uses a momentary action, because the machine stops as soon as you lift your foot. Latching switches stay on after one press, which is a different working style. Check the manufacturer’s listing for the action of the specific pedal you choose.
How do I know a foot pedal fits my power supply?
Identify the foot switch port on your power supply, match the plug style, and read the manufacturer’s listed compatibility. For wireless pedals, your exact power supply model must be named as supported. Test the full chain at a low voltage before using it on a client.


